Control input S ON activates output R.
R is OFF delay (t) after de-energizing of S.
This function requires auxiliary voltage between A1 - A2
(except for example types CNR, C64, C84).
Control input S ON activates output R periodically;
t = tON = tOFF
R is immediately OFF when S is de-energized.
Control input S ON activates output R periodically; starting with pause;
t = tON = tOFF.
The impulse stop is not dependent on S.
This function requires auxiliary voltage between A1 - A2.
Control input S ON activates output R periodically; starting with pause;
t = tON = tOFF
The impulse is stopped immediately by de-energizing of S.
Q is active after reaching the preselected number of pulses.
Q and C can be reset with the reset button.
Q is active for t 75 ...125ms on the preselected pulse.
The cycle starts again at the beginning.
Q and C can be reset with the reset button.
Q is active during the preselected number of pulses
and can only be reactivated after a reset.
Q and C can be reset with the reset button.
Control input S ON activates output R delayed (t).
R is immediately OFF when S is de-energized.
After closing triggering contact S the N/O-contacts of the output relays R1 to R4 close as follows:
R1 after 1x t, R2 after 2x t, R3 after 3x t and R4 after 4x t.
After opening S the closed contacts R1 to R4 immediately release to the N/O-position.
After closing triggering contact S the N/O-contacts of the output relays R1 to R4 close as follows:
R1 after 1x t, R2 after 2x t, R3 after 3x t and R4 after 4x t.
After opening S the closed contacts R1 to R4 release in delayed reverse sequence from 1x t to 4x t to the N/O-position.
Control input S ON activates output R delayed (t1).
R is delay OFF (t2) after de-energizing of S (function E + A).
Control input S ON activates output R delay (t1) for the time t2.
The cycles t1 and t2 are not dependent on S.
Control input S ON activates output R delay (t1) for the time t2.
R is OFF immediately after de-energizing of S.
Control input S ON activates output R periodically.
Pulse (t1) and Pause (t2) are independently adjustable from each other.
R is OFF immediately after de-energizing of S.
Control input S ON activates output R for the time t.
The Impulse is independent of S.
Control input S ON activates output R for the time t.
The time cycle is restarted with a new control input on S (time rest).
S continuous ON has no effect on R.
Control input S ON activates output R for the time t.
R is switched off immediately when a new control input is applied to S.
S continuous ON has no effect on R.
Output R is activated for time t with control input S OFF.
The time cycle is independent of S.
Output R is activated for time t with control input S OFF.
R is switched off immediately when a new control input is applied to S.
Energizing of S ON activates output R periodically; starting with pause.
Pause (t1) and Pulse (t2) are independently adjustable of each other.
R is OFF immediately with S OFF.
Remark:
Allocations of t1 / t2 are solved differently for units of type C50.
Control input S ON activates output R for the time t.
R is activated for the time t2 with control input S OFF.
Times t1 and t2 are independently adjustable of each other.
With S ON the output R switches, that means depending to the previous status ON or OFF.
Je nach Gerät ist der Ausgangszustand netzausfallsicher gespeichert (z.B. AS1), oder aber der Ausgangszustand wird mit Netz aus zurückgesetzt (z.B. AL).
SS = Step-on step-off ( not power failure protected ) :
Mit Ansteuerung S Ein schaltet der Ausgang R ein.
Mit S wieder ein schaltet R aus.
Mit Netz aus wird die function zurückgesetzt, R schaltet aus.
With S ON the output R switches.
With S ON again before time release R switches immediately.
With line OFF the function is reset.
With monitoring clearance by S1 (Y1) i.e. without start cycle bridging, R is activated with the first correct input cycle.
With monitoring clearance by S2 (Y2) i.e. with start cycle bridging (tA), R is activated immediately.
R is deactivated after the time delay tV if the pulse cycle is to long.
R is deactivated for at least 50ms if a failure is detected:
R is activated again with the next recognized correct pulse cycle.
Application note:
This function monitors pulses for correct timing.
It is possible to monitor minimum speeds and motion cycles.
V = Pulse sequence monitoring :
With monitoring clearance by S1 (Y1) i.e. without start cycle bridging, R is activated with the first correct impulse.
With monitoring clearance by S2 (Y2) i.e. with start cycle bridging (tA), R is activated immediately.
R is deactivated after the time delay tV if the pulse cycle is too long.
R is deactivated for at least 50ms if a failure is detected:
R is activated again with the next recognized correct pulse.
Application note:
This function monitors pulses for correct timing.
It is possible to monitor minimum speeds and motion cycles.
Control input S ON activates output R for the time t.
Control input S ON (= operating voltage) activates output R immediately.
R is OFF immediately with S OFF.
R is reactivated only after the time t if S is ON before the set time cycle has expired.
Control input S ON activates output R Star for the time t.
After the dead interval t Star - Delta (contactor switch over time), the output R Delta is activated.
The control input is made via A1 - A2.
Important note:
Outputs R Star and R Delta are internally interlocked.
Kühn Controls SL, all rights reserved.